General Disclaimer:   (HV) (DC) injury or death hazard,   use at your own risk,   may void warranty.

Difference between revisions of "PiPrius"

From My wiki
Jump to navigation Jump to search
(→‎Photos: New photos of battery rack and HV tie-in.)
(→‎Photos: updated descriptions)
Line 25: Line 25:
 
Image:100 1379.JPG|Other end of CAN-View relays # 2-6
 
Image:100 1379.JPG|Other end of CAN-View relays # 2-6
 
Image:100 1381.JPG|Other end of CAN-View relays # 2-6 (closeup)
 
Image:100 1381.JPG|Other end of CAN-View relays # 2-6 (closeup)
Image:100 1438.JPG|Dry fitting new battery rack for 15 Hawker AB modules and regs.
+
Image:100 1438.JPG|Dry fitting new battery rack
Image:100 1439.JPG|new battery rack
+
Image:100 1439.JPG|New battery rack and [[MMPFC]]
Image:100 1440.JPG|new battery rack
+
Image:100 1440.JPG|Will hold 15 Hawker EP26 or Areo AB26's
Image:100 1441.JPG|new battery rack
+
Image:100 1441.JPG|1 or 3 rails shown which will house battery regs.
 
Image:100 1442.JPG|OEM HV tie-in.
 
Image:100 1442.JPG|OEM HV tie-in.
 
</gallery>
 
</gallery>

Revision as of 19:08, 26 June 2006

Rich Rudman of manzanitamicro, Ryan, and PriusBlue, are working on a Prius PHEV implamentation using an upgraded PFC-30 as a DC-DC converter and charger, and Rich is hoping to develop and offer conversion kits.

Misc development related stuff:


Logs

CAN-View Logs from Initial PHEV Test & Tune runs:

Each .zip file contains a main description .txt file similar to the comments which describe it. There are also multiple CAN-View Capture "raw" .txt files and their resultant .csv files. Each capture file is described with dash miles-mpg|CAN-View Trip screen miles-mpg|CAN-View Ah Count down from 10Ah, a description of the trip, and the ammount of recharge.

Photos

Conversion Procedure

General Disclaimer:   (HV) (DC) injury or death hazard,   use at your own risk,   may void warranty.

HV (High Voltage) DC (Direct Current) Warning: Traction Battery Packs, Motors, Chargers, and other HV sources could cause serious injury or death if proper precautions are not taken while working on or around such High Voltage Direct Current sources.

Use this information at your own risk: There is no warranty expressed nor implied and we are not liable for any of your past, present, nor future actions. Even should you perform these modifications to the letter you could still damage any number of components in your vehicle causing it to no longer function. Even if it appears to function properly your actions may cause it to self destruct with collateral damage to surrounding properties other than your vehicle. By utilizing these ideas and instructions in an attempting to enhance national security, reduce gas consumption, vehicle "emissions", your carbon footprint, or smog, you do so at your own risk & peril.

Warranty: In performing some of these modifications you may void your warranty with the vehicles manufacturer.

See also our My wiki:General disclaimer

This is the Initial Conversion Process.

  1. Remove trunk carpet, all storage compartments, and spare tire.
  2. ! ! Be Sure To Remove Orange HV Service Plug ! !
  3. Install HV taps to OEM NiMH battery Pack
    1. Remove rear seat bottom, pull up front edge, unhook rear edge
    2. Remove rear battery deck upholstery 2x tie down clips ?10mm?, 2x tabs
    3. Remove drivers side rear seat back 2x 14mm
    4. Remove drivers side rear seat piller upholstery 12mm, pull up
    5. Remove drivers side trunk pannel upholstery 10mm, 10mm screw, tabs
    6. Remove drivers side OEM Battery brace 7x 12mm
    7. Remove OEM Battery ECU Cover 2x 10mm, 2x 10mm nuts
    8. Add New HV Cables, Notch Here, Trim There, etc, etc
    9. Reassemble in reverse order
  4. Install PFC in drivers side rear wheel well
    1. Locate and drill mount points from pattern
    2. Install ventilation housing and fans
    3. Mount PFC Charger
  5. Install Battery Box
    1. Locate, drill, and press nut body/frame mountpoints
    2. Attatch Electronics Box to bottom of lower battery box frame
    3. Install and fasten lower battery box frame
    4. Populate box with batteries
    5. Install battery regulators and interconnects
    6. Install and fasten upper battery box frame
  6. Install and configure CAN-View.
    1. RL1 = EV-Mode Button trigger
    2. RL2 = ? Voltage dither ?
    3. RL3 = ? Regen mode ?
    4. RL4 = Stock / PHEV mode selection
    5. RL5 =
    6. RL6 =
  7. Connect everything... Replace Orange HV Service Plug

Charge, Drive, and Repeat...

General Disclaimer:   (HV) (DC) injury or death hazard,   use at your own risk,   may void warranty.

HV (High Voltage) DC (Direct Current) Warning: Traction Battery Packs, Motors, Chargers, and other HV sources could cause serious injury or death if proper precautions are not taken while working on or around such High Voltage Direct Current sources.

Use this information at your own risk: There is no warranty expressed nor implied and we are not liable for any of your past, present, nor future actions. Even should you perform these modifications to the letter you could still damage any number of components in your vehicle causing it to no longer function. Even if it appears to function properly your actions may cause it to self destruct with collateral damage to surrounding properties other than your vehicle. By utilizing these ideas and instructions in an attempting to enhance national security, reduce gas consumption, vehicle "emissions", your carbon footprint, or smog, you do so at your own risk & peril.

Warranty: In performing some of these modifications you may void your warranty with the vehicles manufacturer.

See also our My wiki:General disclaimer